1195 – High speed Eco-Friendly Hand Dryer. Compact high speed hand free hand dryer, environmentally friendly, Stainless steel finish. These compact high speed hand dryers are ideal for renovations and areas with 15amp. circuits available. These are also more environmentally friendly due to lower energy consumption. Lowest power consumer on the Eco dryer market. Smallest high speed hand dryer. Air speed of 90m/s provides fast drying time. GreenSpec® listed. LEED Credits: Minimum energy performance: design and construction, EA prerequisite 2. Optimized energy performance: design and construction, EA Credit 1 Materials: Outer casing 18 ga. steel with White expoxy finish. Power Usage: Whole unit is rate at 1000 watts. Heating element: 500 watts. Operating Voltage: 110-120 Vac, 50/60Hz, 0.84 – 1kw. Amps 8.4. Brush motor with dual ball bearing 500w, 29,000 R.P.M. Electrical Safety: Motor thermal protection: contains an auto resetting thermostat which turns the unit off at 105° C (221° F). Drip proof IP X1; Isolation: Class 1. Drying time: 10-12 seconds. Sound Level: 75 dB at 1 M. Sensor Range: 6” (15cm). Performance: Air speed output: 90 m/s (201 mi/hr). Volume: 101.7 m3/h, (59.8 cfm). Air output temperature: 55 degrees C (131 deg, F) Warranty: Complete 5 years from date of purchase. Maintenance: Motor assembly and all working parts must be kept clean from excessive dirt/dust and any form for foreign debris. Failure to maintain unit may reduce performance and result in void of warranty. Installation: Supplied with mounting template, instructions, screws and anchors. ... More Info >
Hands free hand dryer, white finish. Touch free sensor is activated when hands are placed within the set range under spout. Approximately 20 second drying time. Voltage: 110 volts, Power consumption: 2200 watts, Sound level: 61-67 db. Brush less 100 watt 3,450 rpm motor. Sensitive distance of sensor: 4-12" (10-30 cm). Touch free sensor is activated when hands are placed within the set range under spout. There is a .6 sec delay for on and a 2 second delay for off. The power will be cut off automatically in cases of irregular use over 120 seconds, sensor will reset during normal use. Sensor is 100% moisture proof. Wind measure: 161 cfm, (274 m3/h), Wind velocity: (16.5m/sec). ... More Info >
Hands free hand dryer, high speed, 120 volts, porcelain white finish. Ideal for areas with limited space requirements and installations promoting power conservation. Blue L.E.D. Helps target ideal drying area. Drying time: 10-12 seconds. Outer casing is 16 ga. drawn steel with porcelain enameled finish. Stainless steel: 16 ga. Whole unit is rated at 1600 watts. Heating element is 900 watts. Dual ball bearings brush motor is 700W, 18000 R.P.M. The decibel reading at 1 meter is 78. Operating Voltage: 110-120 Vac, 50/60Hz, 1.3 – 1.6 kw. Amps drawn: 14.5 Electrical Safety: Motor thermal protection: contains an auto resetting thermostat which turns the unit off at 105° C (221° F). Motor overload protection: motor assembly has a replaceable fuse. LEED Credits: Minimum energy performance: design and construction, EA prerequisite 2 Optimized energy performance: design and construction, EA Credit 1. Heater thermal protection: An auto resetting thermostat turns the unit off at 85° C (185° F). Drip proof: IP X1; Isolation: Class 1. Performance: Air speed output: 100 m/s (225 mi/hr). Sensor range: 7” (18cm). Warranty: Complete 5 years from date of purchase. Maintenance, Exterior: Unit may be cleaned with soap and water or approved cleaning products/sanitizers. Interior: Motor assembly and all working parts must be kept clean from excessive dirt/dust and any form of foreign debris. Failure to maintain unit may reduce performance and result in void of warranty. Installation: Supplied with mounting template, instructions, screws and anchors. ... More Info >
1196 – High speed Eco-Friendly Hand Dryer. Compact high speed hand free hand dryer, environmentally friendly, Stainless steel finish. These compact high speed hand dryers are ideal for renovations and areas with 15amp. circuits available. These are also more environmentally friendly due to lower energy consumption. Lowest power consumer on the Eco dryer market. Smallest high speed hand dryer. Air speed of 90m/s provides fast drying time. GreenSpec® listed. LEED Credits: Minimum energy performance: design and construction, EA prerequisite 2. Optimized energy performance: design and construction, EA Credit 1 Materials: Outer casing stainless steel: 18 ga. Power Usage: Whole unit is rate at 1000 watts. Heating element: 500 watts. Operating Voltage: 110-120 Vac, 50/60Hz, 0.84 – 1kw. Amps 8.4. Brush motor with dual ball bearing 500w, 29,000 R.P.M. Electrical Safety: Motor thermal protection: contains an auto resetting thermostat which turns the unit off at 105° C (221° F). Drip proof IP X1; Isolation: Class 1. Drying time: 10-12 seconds. Sound Level: 75 dB at 1 M. Sensor Range: 6” (15cm). Performance: Air speed output: 90 m/s (201 mi/hr). Volume: 101.7 m3/h, (59.8 cfm). Air output temperature: 55 degrees C (131 deg, F) Warranty: Complete 5 years from date of purchase. Maintenance: Motor assembly and all working parts must be kept clean from excessive dirt/dust and any form for foreign debris. Failure to maintain unit may reduce performance and result in void of warranty. Installation: Supplied with mounting template, instructions, screws and anchors. ... More Info >
Hands free hand dryer, high speed, 120 volts, Stainless Steel Blue L.E.D. Helps target ideal drying area. Drying time: 7-10 seconds. Whole unit is rated at 1600 watts. Heating element is 900 watts. Dual ball bearings brush motor is 700W, 18000 R.P.M. The decibel reading at 1 meter is 78. Materials: Outer casing is 16 gauge drawn steel with Stainless Steel finish: Operating Voltage: 110-120 Vac, 50/60Hz, 1.3 – 1.6 kw. Amps drawn: 14.5. Electrical Safety: Motor thermal protection: contains an auto resetting thermostat which turns the unit off at 105° C (221° F). Motor overload protection: motor assembly has a replaceable fuse. Heater thermal protection: An auto resetting thermostat turns the unit off at 85° C (185° F). Drip proof: IP X1; Isolation: Class 1. Performance: Air speed output: 100 m/s (225 mi/hr). Sensor range: 7” (18cm). Dimensions: 7.125″D x 8″W x 11″H. Installation: Supplied with mounting template, instructions, screws and anchors. LEED Credits: Minimum energy performance: design and construction, EA prerequisite 2 Optimized energy performance: design and construction, EA Credit 1. Maintenance: Exterior: Unit may be cleaned with soap and water or approved cleaning products/sanitizers. Interior: Motor assembly and all working parts must be kept clean from excessive dirt/dust and any form of foreign debris. Failure to maintain unit may reduce performance and result in void of warranty. Warranty: Complete 5 years from date of purchase. ... More Info >